• Welcome to Support Forum: Get Support for Patch My PC Products and Services.
 
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - coover

#1
Whenever I attempt to open "Patch", I get an error message that my computer is unable to reach the "Patch" server. I am having no problems reaching other websites. Perhaps it is down for maintenance?Screenshot 2022-09-26 111152.png
#2
Right now, there are updates available for KC Software's SUMo and Crystal Disk Info. SUMO has been available for several days and CDI for, probably 24 hours, at least, but Patch My PC does not see those updates or install those updates even when manually requested.

I do not know how the software knows when updates are available, but, at least with these two, it seems like it is taking too long for it to happen.
#3
Looks like Ccleaner Portable may be gone with version 6.Patch does not have an update and none on Piriform page.
#4
Everytime I download Foxit PDF Reader on Patch My PC, the download takes a very long time. I realize that this application is large, about 160 MB, but my internet download speed is over 200 Mbps and at that speed (which I just verified is 234.41 Mbps), it should not take many minutes to download. In fact, I just downloaded the application from the MajorGeeks website and the download took seconds, but the Patch My PC website seems to be taking forever. And this is not unusual. For the last several years, Foxit PDF Reader has downloaded on Patch at speeds approaching that of a turtle.

I realize the problem is not my internet connection, it is quick enough, and the problem, I assume, is not from Patch, as other applications are not this slow ... so the problem must be by the server that Patch downloads the application.

Can something be done to make the changes that must be done to make the Foxit PDF Reader download, to download at a reasonable rate in the future?
#5
I have Rufus (Portable) version 3.17.1846. Your application (apparently) does not like this and wants to install version 3.16.1836. Because of this, every time I use "Patch My PC" on any of my 9 machines, I must stop, go down to the bottom of "Patch", and remove the check mark to stop the installation of the older version.  :-\
#6
I no longer use Driver Booster because of their nags. It's not bad software, but the nags are horrible. I now use "Snappy Driver Installer Origin" to update my drivers, and, I believe, I get better results than I would with Driver Booster. That said, Driver Booster is easy to use, while SDI Origin can be confusing for folks that do not have a lot of knowledge about computers and software. I do recommend SDI Origin. It's free, it offers ALL drivers (unlike Driver Booster), and does not nag you to upgrade or buy their other software.
#7
I ran "Patch ..." today and found nothing to update. I then ran KC Software's "SUMo" and it told me that "Privazer" could be updated (from 4.0.26 to 4.0.27). I then reopened "Patch ...", and though it did not show an update for "Privazer", I manually selected it. Interestingly enough, the installer indicated that it was installing 4.0.26 again, but when the installation was finished, I noticed that 4.0.27 had been installed.

This brings another question. Not using "Patch ...", I sometimes find that an application I use can be updated. But then I find that the update is not on "Patch ...", so I wait try the update later, I have found applications that are not updated on "Patch ..." for several days but can be easily found by searching for the app or using a webpage such as "MajorGeeks". It would seem to me that it should be important to the "Patch ..." developers to get those updates as soon as possible and not wait until the update is several days old.

That said, I love your application, have it installed on all 8 of my Windows 10 (or 11) computers and use it daily on each.
#8
Apparently fixed by either Patch My PC as I've had no updates to Windows 10. I no longer have this issue.
#9
Same issue here ... with all 6 of my PCs. Apparently an MS .NET error. I hope somebody is able to fix this quickly.
#10
It still wants to download the file already installed ... see attachment
#11
Thanks, Guys!
#12
I noticed that Crystal Disk Info has been updated on the MajorGeeks webpage to version 8.8.2. Patch My PC was still showing 8.8.1. So I first used "Patch ..." to manually update. It did not. I went back to MajorGeeks and updated to 8.8.2. Again back to "Patch ..." and it showed an update back to 8.8.1 so I allowed it to do it, just tp see what happens. It reinstalled the outdated version 8.8.1. I still had the 8.8.2 installation file on my computer so I again ran that.

Please fix your problem. Things like this should not happen.
#13
The free Backupper version is excellent. I back up my computer using the "Clone" feature. I rotate 3 separate external Hard Drives, one each day, and clone the internal drive, allowing me to go back 3 days if necessary. It takes about 30 minutes for the daily manual backup.  ;D

The AOMEI Partition Assistant (Free) is also excellent, and it will also clone a Hard Drive, but requires a the user to reboot the computer and clones the dish outside of Windows. It takes a little longer to complete the clone.

AOMEI's Free versions do not have all the features of their Shareware versions, but the user can do much more with these free versions than is allowed with similar free software from other publishers.
#14
I'm going to guess that when Microsoft finally fazes out it's own version of Edge (which should be fairly soon), it will update automatically or update with Windows Update regularly.
#15
I am one of those folks that want to download and install every update, minor or major, in order to make sure that the application has as few bugs as possible, but as davev indicates, others do not. It makes sense that those folks be given a choice to accept only major changes. Perhaps they could indicate this by checking (or unchecking) an Option box. Of course, this would not only mean the adding of another option, but a loop would have to be added to the program to keep PMPC from doing minor updates. I am not sure just how difficult this would be to the programmer(s), but it seems to me that it would be a fairly easy change.